Technical Parameter of Rotary Kiln
Model (m) |
Technical data |
Reduction drive |
|||
Speed (r/min) |
slope (%) |
capacity (t/h) |
type |
ratio |
|
Φ1.2×35 |
0.5-1.6 |
3 |
0.5-1.8 |
PM650 |
31.5 |
Φ1.6×32 |
0.158-0.258 |
3 |
1-2.5 |
PM750 |
31.5 |
Φ1.8×45 |
0.66-1.98 |
4 |
2-3.5 |
UT2-110 |
25.57 |
Φ1.9/1.6×36 |
0.53-1.59 |
4 |
2.5-3 |
JZQ750-1 |
25.57 |
Φ2.1/1.8×36 |
0.5-1.51 |
4 |
4 |
UT2-110 |
25.57 |
Φ2.2×50 |
0.125-1.25 |
3.5 |
4 |
ZS145-11 |
27.55 |
Φ2.5×50 |
0.516-1.549 |
3.5 |
5.5 |
ZS165-7 |
27.55 |
Φ2.7×42 |
0.6-2.3 |
3 |
13 |
ZS145-3-1 |
27.55 |
Φ2.8×42 |
0.5-2.5 |
3 |
14 |
ZSY355-50-1 |
27.55 |
Φ3×88 |
0.44-1.3 |
5 |
12.5 |
ZS199-5-4 |
27.55 |
Φ3.5×29 |
0.6-1.7 |
4 |
10 |
ZS165-4 |
27.55 |
Φ3.6×42 |
0.5-1.5 |
3.5 |
22 |
ZS165-4 |
27.55 |
Φ4×32 |
0.3-1.48 |
4.25 |
12 |
ZS165-4 |
27.55 |
Φ3.2×64 |
0.4-1.5 |
4 |
8-10 |
ZL130-16 |
31.5 |
Φ3.2×118 |
0.3-1.4 |
6 |
17 |
JH500C-SW-71 |
28 |
Φ3.5×125 |
0.28-1.4 |
5 |
21.8 |
ZS165-4-1/2 |
27.55 |
Φ3.×145 |
0.345-1.38 |
6 |
25 |
ZS165-3-1/2 |
27.55 |
Φ3.8×58 |
0.4-1.5 |
3 |
20.8 |
ZSY500-40 |
27.55 |
Brief Introduction and Application of Rotary Kiln
Rotary kiln is the main equipment of dry and wet production line of cement clinker and cement kilns for calcining cement clinker, the sub-dry production of cement kilns and wet process cement kilns two categories. Cement rotary kiln addition in environmental protection, the use of cement kilns burning hazardous waste, refuse, which not only waste minimization, harmless, but also will use waste as a fuel saving of pulverized coal to achieve the waste of resources.
Rotary kiln belongs to building material equipment, which can be divided into cement kiln, metallurgy chemical kiln and lime kiln according to different materials. Rotary kiln is used for making of cement clinker and there are dry and wet methods to make activated carbon. Metallurgy chemical kiln is used in metallurgy industry and ironworks for iron ore, chromium ore and ferronickel ore calcimine. Rotary kiln is used for calcimine of high aluminum vandal ochre in refractory material industry; for calcimine of calotte and aluminum hydroxide in aluminum manufacturer; for claiming of chrome sand ore and chrome powder ore in chemical plant.
Feature:
1. High quality, high output, low cost
2. High precision temperature control
3. High level automatic running
4. Easy to setup, operate and adjust, and customizable
Structure Features and Operation Principle of Rotary Kiln
1.Rotary Kiln Supporting device apply rolling bearing ( few with sliding bearing) to simple the bearing structure to slow down the kiln power consumption and it also improve the maintenance and inspection conditions.
2. Catch wheel: including two kinds mechanical wheel and hydraulic pressure
3. Gears: single or double. Control the rotating speed by buncher, DE machine and frequency variable motor. Be reliable, energy-saving, and efficient.
4. Cylinder type bolster: lower bolster has three types: fixed, zoom and floating. The structure is simple, replacement is convenient and won’t hurt cylinder.
5. Sealing equipment: there are many kinds for choice according to kiln models, including air cylinder edge sealing, spring edge sealing, and graphite block sealing and combination for above. The feather is adaptive for cylinder rotating and swing. And sealing effect is very good.
6. Rotary Kiln head hood: including stationary type and flexible type.
7. Transmission device apply speed adjustable motor with big speed adjustable range, stable operation, easy to maintenance advantages. Our Rotary Kiln has slow disk kiln structure, which is composed by Diesel engine, gearbox, etc. It could continue to operate when electric stops, its operation is very flexible and convenient and easy for the kiln maintenance and inspection.
The rotary kiln is a cylindrical vessel, inclined slightly to the horizontal, which is rotated slowly about its axis. The material to be processed is fed into the upper end of the cylinder. As the kiln rotates, material gradually moves down towards the lower end, and may undergo a certain amount of stirring and mixing. Hot gases pass along the kiln, sometimes in the same direction as the process material (co-current), but usually in the opposite direction (counter-current). The hot gases may be generated in an external furnace, or may be generated by a flame inside the kiln. Such a flame is projected from a burner-pipe (or "firing pipe") which acts like a large bunsen burner. The fuel for this may be gas, oil or pulverized coal.
Why choose us
1. We Are Factory with 3 Big Production Bases ( NOT Dealer )
All machineries from Winnermac Mining Machinery Manufactory are made by ourselves, with lower price, good quality.
2. Full and perfect service
♥.Pre-sale services: enthusiasm
We provide you with the prophase plan, process flow design
and manufacturer equipment according to your special demand.
♥.Sale services: servant
Send technicians to the jobsite for guiding the installation and adjustment,
training operators and finishing the check and accept together with you
♥.After-sale services: faithfulness
To establish long term friendship, we will regularly pay return visit to customers.
3. Product Delivery
We have developed long and good relationship with many shipping agents. Ocean freight partners are: APL, COSCO, OOCL, CSCL, MSC, etc.
4. If you are new for this business, we will help you
Many thanks for your trust; we can provide you with design scheme for complete production lines, spot inspection and operator training according to your demand.
Over 26 years experience in this field
belt conveyor,bucket elevator,screw conveyor,vibrating feeder,vibrating screen,rotary screen,etc.